Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > Brakes, Suspension & Body Chassis > control arm and rear rebuild

Brakes, Suspension & Body Chassis The place to go for answers on brakes, suspension, camber, alignment and more.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: control arm and rear rebuild Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2013 01:08 PM
gtferrari i had to replace one rear corner on my 08 when i went to upgrade the springs and absorbers. the nuts spun off with no fuss but as the bolts came out they seized. turns out i had a bad bushing. paid $127 for anew control arm from ford (it was the only option in my area) seems to run 35-55 anywhere else and $12 per bolt (ford only). there was no room to cut them out and i went through a lot of sawzall blades (spring for the hardened steel ones). its an easy chore to do in you garage if you have a jack and stand. torching might be easier but burning a bushing inches from your head isnt the wisest thing... you will definitely need a 4 wheel alignment afterwards (~$90). i would say total time per corner using the sawzall 3hrs (if you need to cut both bolts).
04-28-2013 09:37 AM
mikebontoft V8 swap. Sounds easier than dealing with those stupid bolts. haha.
04-28-2013 09:29 AM
Chris_HT On the rear end that much rusted, you will fight every bolt, and need to replace nearly everything.

Try to simply unbolt (be f... careful not to drop it on your head) whole crossmember/subframe, and perform work off the car. Maybe even replace whole sub frame assembly from other Focus.

I'm just finishing my rebuild.
04-28-2013 08:37 AM
mikebontoft looks like they got it covered...so all I'll add is... nice VT500 I spy through your wheel :D

(at least I think it's one... 83-84?)
04-28-2013 08:21 AM
felixthecat
Quote:
Originally Posted by TEK30001 View Post
I am looking to get:

http://www.massivespeedsystem.com/_m...s/g-62761.aspx


And

http://www.massivespeedsystem.com/_m...s/g-62727.aspx

For the most part I get all my thing from this web page or is there a better website?
Those will work. You'll find the toe-links will give the rear end more responsive.
Try CFM= centralfloridamotorsports, Steeda, Fwerks, Tirerack.
04-27-2013 09:27 PM
TEK30001
What is the best Rear Toe Control Arms and Adjustable Camber Arms

I am looking to get:

http://www.massivespeedsystem.com/_m...s/g-62761.aspx


And

http://www.massivespeedsystem.com/_m...s/g-62727.aspx

For the most part I get all my thing from this web page or is there a better website?
04-17-2013 01:14 PM
my_beautious_ZX3 ahhh...beautiful pics! Isn't macro mode a minor miracle?!

penetrating lube is definitely worth a shot, esp. considering your vehicle isn't very old.

Unfortunately though, those bolts tend to seize on the inside of the LCA, so a gallon of PB might not even work. But, who knows - reapply the PB and let it soak for a couple of days; then take a whack at the bolts again. Don't compromise your personal safety.

As for which power tool is best to use, I personally can't advise, because at this point I said "f--- it!" and let my mechanic do it; he later said it was one of the worst jobs he's encountered. Search the forum archives - there are posts by folks who have done this dirty deed, but I don't know how much detail they mention. You could always PM them for details.

Regardless of which method you use, note how poorly the cross member in your photo is made! Very thin sheet metal and further compromised by corrosion. So, take care not to damage it when destroying those bolts. Since the LCA is gonna be trashed anyway, focus your frustration in its direction.
04-17-2013 11:02 AM
cmb1120 these are what the bolts look like on rear lower control arms. I just sprayed them with pb oil. I cannot get them to turn at all. Any ideas that do not involve using an axle grinder or sawzall?



04-17-2013 03:22 AM
elsolo Well, sounds about what I would expect.

By the time the bushings in any one rear control arm are wasted, the rest are not far behind. I wouldn't do one new lower control arm and leave the other waiting to fail. It's rusty, so I would expect to have to cut at least one bolt off. Those bolts, like many of Ford's, should be replaced anyhow.

If it were mine, I would expect to replace all bushings and fasteners, including the cam bolts for setting the rear toe-in. Replacing the bushings means new control arms.
04-16-2013 11:24 PM
my_beautious_ZX3 seems like alotta rust for an '06, but then you do live in the rust belt.

the photos are kinda blurry. If you took them with a digital camera, can you replace them with ones shot in macro ("close-up") mode? Macro is sometimes designated by a flower icon. Shots of bolts & rubber would be helpful, as would a couple that are a little further away, to give us a "big picture" view of each suspension component. Even so, the best we're gonna be able to do is second-guess your mechanic.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:41 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.