|04-25-2013 08:10 PM|
|04-25-2013 07:34 PM|
|SilverST05||Nice. I might try this soon.|
|07-03-2010 12:09 AM|
|clinton j||i did my eyelids with vinyl.. i liked the look, but the glue didnt hold to the vinyl, just to the light on one light and fell off a few weeks later... proubly just defective glue or what not, not a big deal.. i thought about painting them on too, but was thinking about useing nite shade.. with some clear coat over top of them... what do yall think bout that idea?|
|07-02-2010 03:45 PM|
|zx360||I only said the blue stuff to get the shape you like. I agree with chris, use the green 3m stuff for masking not blue tape.|
|06-29-2010 02:36 AM|
|norcalfocus01||Don't use the regular blue painters tape. Use either 3M 2080 blue tape, or the 3M green automotive tape. They have a thinner paper, so the line where you mask it off will not be as high and ridged.|
|06-28-2010 11:12 PM|
|dreamerbigdream||Thanks for all the info. This seems like something I should be able to do with the free time I usually have.|
|06-28-2010 12:24 PM|
I did mine just a little while ago. I was painting them on so I had to have it right the 1st time. This is what I learned. 1: Your headlights are probably not the same height or angle as mounted. On my 7, the passenger side inner corner sticks out much further than the drivers side. I made metal templates of the proposed eyelid and discovered that the angle difference affected how the eyelids appeared from about 10 feet away (passenger side appeared lifted). I also found that the templates were not a dependable method as there placement was subject to movement upon multiple removal/applications. I suggest you get some blue painters tape (narrow), and some sharpies (3 different colors. they will wash off the lexan so no worries). Also a ruler with an end catch. metric preferred.
Measuring accurately and replicating on the opposite side can be a challenge depending on how curvy the headlamp is. I found that putting down some tick marks on the bottom and sides was helpful (use the ruler end catch to 'hook' the headlamp edge). Once you have some measured ticks mark down, you can then play with the painters tape to find the amount of eyebrow you want, and be reasonably assured that you have both sides equal (or at least split the difference between appearance and accuracy). It took me about 3 hours to figure this all out which really is not to bad I guess (I spent an hour dorking with the templates). Notes: 1:Do not trust paper implicitly. It can stretch. So if you put a tick mark on the tape say, remove and reapply later it may be off a tad. Just expect this. 2: If you spray, insure you have LOTS of drop cloth coverage for where you do not want the paint to go. norcalfocus01 has a thread (sticky?) discussing this. 3: Depending on color, insure you have an acceptable color match (one benefit of metal templates was I could paint them and check this 1st).
That is the highly accurate >anal< method.
Edit>Add> It is also best practice that, once you have your paint lines drawn, remove the headlamps for painting. This negates the need for all the drop clothes and also insures you get a nice clean paint line near the seals.
|06-28-2010 11:14 AM|
Best thing would be blue painters tape... make off the eyelid where you want painted and see how it looks.
If you had a 00-07 i would send you my paper templates i used to make the vinyl eyelids i sell... i dont have any for 08-10 yet though.
|06-28-2010 08:56 AM|
|milkweed||try this how to thread http://www.focusfanatics.com/forum/showthread.php?t=166911 hope it helps|
|06-28-2010 05:39 AM|
Eye lids on headlights
I've searched the forum and wasn't able to locate a thread that had a how to section in it. Is there a template that can be followed for painting on eye lids or general instructions on the proper way to do it? I like the look of them but don't want to screw up my headlights by doing it incorrectly or making it look retarded by making them to big or slanted. If there is already a thread for this please just link it in here and I'll read it. Thanks.