|04-15-2014 08:40 PM|
|echan||Does anyone have any recent info how to fix the non-working horn on a 2012 SEL Hatchback? Just noticed it today.|
|03-25-2013 12:39 PM|
|amc49||I too use the public library, the 'secret tool'. Reference section chock full of factory service and electrical manuals. I xerox copy what I need since I don't cell. Prefer the physical copy anyway...........|
|03-24-2013 10:02 PM|
|2003focusowner||Tried this week and haven't had any luck yet. Still no sound from the horn........|
|02-21-2013 01:41 AM|
|tmittelstaedt||I went to my local library where they have an Alldata subscription and looked it up - sorry I didn't save the darn number. It was kind of irritating because I had just a week earlier replaced the horn on mine with one from a wrecker so I could have saved the $10 and gotten a new horn. :-(|
|02-19-2013 08:22 PM|
|2003focusowner||Would you happen to know where we would find the TSB?|
|02-18-2013 02:26 AM|
|tmittelstaedt||It's probably too late for this but you should know that Ford has a "secret recall" on the horns on the early Focuses. The NHTSA and Ford cut a deal on this - in exchange for replacing a failed horn no questions asked, NHTSA didn't require them to do a formal recall. There is a Ford TSB on this that specifies free horn replacement.|
|02-17-2013 04:21 AM|
Most horns are that type if you look deep enough. Simply breaking the vibration setscrew loose can often get them working again, or cleaning up breaker point contacts to make them low resistance again. Water entry or rust usually the problem. I haven't bought a horn in 40 years, I always can fix them. I, like sailor learned long ago from motorcycle horns. Only reason to buy one is for when they cheap out and give you only one and adding the opposite tone then really ramps up the noise.
I wouldn't be spraying WD40 in there, once it hits current, the current will convert it to something (bubblegum) that does not help passage of that current. It's not electrical cleaner.
|02-16-2013 06:07 PM|
|02-16-2013 05:36 PM|
Good to know the stock horn is that type!
VERY common "fix" I did often on motorcycles. They get used so seldom, plus the change in stiffness of materials from age... re tuning them usually "fixes" them for quite a while in my past experience..
Thanks for the update!
|02-16-2013 04:06 PM|
This is just an update to this thread.
When I recently discovered my horn had quit working i went through all the steps to test and make sure it was actually getting power. Once I determined that it was the horn that was faulty I removed it and bench tested again with an old battery and some alligator clips on the terminals and it still didn't work.
I went thru the process of shooting WD-40 into the horn opening and sloshing it around and still nothing.
A couple weeks had passed and the horn still sitting on the bench I decided to test it again by putting the power to it and still nothing.
The difference this time was I figured i had nothing to loose and tapped the side and back beside mounting bolt with a small piece of brass rod and it started to operate intermitenly, but not steady or very loud tho.
At that point still thinking i would be throwing in the garbage I decided to mess around with the adjustment screw that is factory covered with silicon and ended up removing it and shooting a little bit of WD-40 in the hole.
This is where things get interesting and remember that i still have the leads connected so the horn is getting power as i'm putting the ajdustment screw back in the horn begins to function but this time with a steady tone.
Now I simply adjust the screw til the horn seemed the loudest and put a new bloob of silicon on the head of the screw and reinstall the horn back on the car, push the horn pad and it seems to function as it should.
Just thought I'd pass on the info for anyone that wants to save a few bucks and feels like a little challange.
|This thread has more than 10 replies. Click here to review the whole thread.|