Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus ST > Focus ST EcoBoost Performance (2013-Current) > Review: FSWERKS 3" exhaust (pics & vids)

Focus ST EcoBoost Performance (2013-Current) The place to chat about the 2.0L EcoBoost engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Review: FSWERKS 3" exhaust (pics & vids) Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-28-2013 05:02 PM
bigdesignmachine My Race Exhaust I had on my 2000 SE was not a Magnaflow muffler
01-28-2013 02:09 PM
Brabs_Weather
Quote:
Originally Posted by Ocysp View Post
FSWERKS uses a Magnaflow muffler with their own 3" piping all the way back. The Magnaflow 15155 utilizes a 2.5" pipe.

Have fun and drive safe,
-Ocysp
Ok. Wonder how much R&D goes into that. Have they always used Magnaflow on there exhaust with other FF.
01-28-2013 11:38 AM
Ocysp
Quote:
Originally Posted by Brabs_Weather View Post
So the FSWERKS uses a MAGNAFLOW exhaust. I thought they made there own version of the exhaust. Are they just reselling the Magnaflow version 15155 and adding the tip?
FSWERKS uses a Magnaflow muffler with their own 3" piping all the way back. The Magnaflow 15155 utilizes a 2.5" pipe.

Have fun and drive safe,
-Ocysp
01-28-2013 11:33 AM
Brabs_Weather So the FSWERKS uses a MAGNAFLOW exhaust. I thought they made there own version of the exhaust. Are they just reselling the Magnaflow version 15155 and adding the tip?
01-28-2013 11:06 AM
Ocysp
Quote:
Originally Posted by FocusSportTECH View Post
The video you made is with a downpipe without any catalytic converter right? Just seems louder then our standard cat-back setup is why I'm asking.
Yep. CP-E DP without a cat.

Have fun and drive safe,
-Ocysp
01-28-2013 06:52 AM
Slammed_2.0 Saw this on focusst.org.

This is with the 3" downpipe. Sounds a little much with the DP. Hopefully you'll come with a stealth system with the DP.
01-28-2013 01:43 AM
FocusSportTECH The video you made is with a downpipe without any catalytic converter right? Just seems louder then our standard cat-back setup is why I'm asking.
01-28-2013 12:34 AM
WhiteTite Thanks for the video, I have the FSWERKS stealth on our Ti, which I modified by adding a magnaflow where the stock muffler is because it was too loud and had way more drone for my liking. I can hear that this exhaust is not for me on my ST, but great write up and video, enjoy!
01-27-2013 11:44 PM
ZXthrizzle05 thank you for the post. would help a lot of people before installing. when idid my custom 3 inch a month ago I had no references to how it would sound afterwards wich was why I made a video like yourself
01-27-2013 11:09 PM
Ocysp
Review: FSWERKS 3" exhaust (pics & vids)

So, I figured I'd post my review here for the FSWERKS ST exhaust:

The FSWERKS exhaust is a 3" stainless steal exhaust for Focus STs. It comes with all the necessary parts to install, minus the 3" downpipe that you should already have ;D. It comes with dual tips with the "FSWERKS" logo/text etched on the top. Also includes a Magnaflow muffler. All parts are clamped together; no welding necessary.





So, I decided I would do all the installation work myself. I don't have access to a lift so I made use of my ramps to get my car high enough to be able to crawl under it. This provided JUST enough room. It would have been a little easier if the car was lifted about 1 more inch. I had my ramps setup on the rear wheels. I had to use a jack to lift up the front driver side a couple of inches. I did not lift it up enough for the tire to come off the ground and I used a jackstand for extra safety. All this was necessary to get enough room to get it attached to the downpipe.



To get the stock exhaust out, I had to make a cut (pic above) right before the piping turns up to make its way through the suspension. Getting the stock piping removed was a bit difficult as my car was still too close to the ground. I eventually got it all out without having to raise the car up more.

While installing I ran into the same problem, I just didn't have enough room. Had to bend some of the heat shielding around to get all the pieces of the pipe situated where they needed to be.

When I finally got everything situated, all of the exhaust hangers attached, clamps snug, and tip positioned correctly, I began the final tightening of the clamps. I was using a smaller 12" long torque wrench to tighten the clamps. I seemed to not be able to get the clamps tightened enough. The 3rd pipe kept rotating within the 2nd pipe causing the end of the exhaust (tips) to hang low. I went to my local autoparts store to borrow a longer torque wrench so I could get more torque on them. I ended up overtorquing the clamp and sheering the bolt in half.



I take blame for this one, as when it sheered I had it at 110ft/lbs. So, I decided to take the clamp off of the tips and use it on the section of piping that I broke the clamp on. I started torquing it down again, and it sheered the bolt in half at 70ft/lbs! I think I uttered every explicit word I know of. So, I went to the local autoparts store to see if they had any clamps I could buy. They had the standard "U bolt" style clamps, and a really wide band clamp. The band clamp was the same setup as the FSWERKS clamps, it was just wider and utilized two bigger bolts instead of one. The spacer shown in the picture below I ended up cutting in half so that I could re-use the old clamp with the new bolt and spacers. I put it back on, and got it torqued down enough that it did not move any more. I used a U-bolt clamp to fasten the tips to the rest of the exhaust.



All in all, I'm very pleased with the exhaust. I really wish I would've had better luck with the clamps but I love fixing things, so it wasn't that big of a deal. Oh yeah, I would not recommend this exhaust if you're wanting something quiet or without drone.



And now for the best part. The video:
YouTube Video
ERROR: If you can see this, then YouTube is down or you don't have Flash installed.


Please "Like" my post if any of this was helpful or if you enjoyed the video. Also, if you have any questions about the installation feel free to ask!

Have fun and drive safe,
-Ocysp

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:01 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat