Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > ATX shift kit

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: ATX shift kit Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-07-2013 08:46 AM
Diesel I found an article searching "4f27e" in google. They built a race trans for a zx5 that they were going to turbo.
They uoed the line pressure about 5% mechanically because they didn't want to get in to the ecm. Write of story claims it made a big difference in the shifts.

Everything else I read is people complaining about the low line pressure of these transmissions. I've only built stardards lately and mostly big CDL ones. I haven't onpened a ATX trans since the 700r4's
01-07-2013 06:18 AM
amc49 Nah, most I've played with actually had a pressure setting bolt, or a spring changed out. More than one spring shown in kit too. Drilling holes is more of a momentary timing and quick/slow pressure rise mod thing, or pressure relief rather than increase. Its' result is usually a TEMPORARY effect. For pressure regulation to the entire trans the effect has to be bigger than that. I wouldn't be surprised if the drill was to open a restriction to those small accumulators to let the errant one fill a bit faster when worn trans is cold. Obvious from kit parts that the accumulators are a heavy wear issue.

Interesting reading the hydraulic flowchart for the trans. There are TWO pressure regulators, a main and one for solenoids A/B. The main one is spring loaded like all, but in this case the EPC solenoid pipes output into that spring chamber to add to the spring's tension and modify the line pressure itself. Simply adding a shim or a stiffer spring would definitely bump up the base line pressure with no added input from the EPC. Line then goes to the solenoid regulator to be modded again and then tees back into EPC input that seems to get regulated by blowing off into space like a regular bypass on an oil pump, just electrically regulated instead of sprung valve. I could not find in/out circuits like the other solenoids have, only in at EPC. A delicate balance going on between line, EPC and sols. A/B...............
01-07-2013 02:26 AM
elsolo It's usually done by enlarging a hole in the separator plate, and I do see a drill bit in the kit photo.
01-07-2013 01:50 AM
amc49 There could easily be a base mechanical pressure setting that solenoids modify........
01-06-2013 09:20 PM
elsolo Lentec claims to increase line pressure w/o getting into the ECU program.

The computer dictates the EPC solenoid's output state, but I don't think it has any way to reference the actual pressure.

It would be kinda like changing fuel injector size on an open loop control system, it will flow more than it thinks it is.
01-06-2013 07:28 PM
1turbofocus The ECU control's the ATX psi , if you want to raise the trans psi and change the shift points the only way to do this is with a tune

Tom
01-06-2013 07:23 PM
amc49 Note the english used there in description, It may very well mean the spring is stronger to not break, that may have nothing to do with bumping up line pressure. A simple different heat treat on replacement spring would do that. I think they are thinking in terms of recovering stock factory performance only there.
01-06-2013 04:45 PM
Diesel I found a mag that did a build up on the trans and they increased line pressure to make the focus better. So that's why I considered it.
01-06-2013 02:41 PM
elsolo I looked all over the net for user experiences with that kit, couldn't find any.

I have considered giving it a shot, all my auto's have firmed up shifts except the Focus.
01-06-2013 07:23 AM
Diesel
ATX shift kit

I've seen complaints on here and else where about the 4f27e (1st gen focus axt) having low line pressure. well I found a kit that replacs a spring and ups the pressure. I'd seen a performance shop ups the pressure by about 5%

Has anyone done this to theirs?

Here is a kit I found: (this isn't an ad I'm looking for others advive. Won't let me copy pic.)
http://transmissiontechnologies.com/...-kit-ford.aspx
Shift Correction Package

This valve body kit deals with these problems:

* Soft shifts and flairs
* Premature band failure
* Code P0741 (T.C.C. slippage)
* Broken solenoid P.R. valve spring
* Worn or damaged accumulator bores
* Accumulator Buddy "Tool" Included
* Newly designed accumulator pistons included

The 4F27E kit includes Superior's patent pending billet 1-2 and neutral/ drive dual sealing ring accumulator pistons. This kit also contains one of our patent pending Accumulator Buddy brushes so no other tools or fixtures are required. The pistons and brush allow you to reuse previously discarded cases that would not have sealed due to premature ware. The 4F27E kit also includes a new, stronger solenoid pressure regulator valve spring to replace the frequently broken stock spring.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:24 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.