Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > Coolant in #2 spark plug hole of Zetec.

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Coolant in #2 spark plug hole of Zetec. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-01-2013 07:03 AM
tideiscup good idea, Mild acid to clean any corrosion around and on the plug.and Penetrating loctite to seal it up.thanks
01-01-2013 02:33 AM
emsvitil Good News:

The antifreeze isn't leaking from the pipe plug.




Bad News:

The antifreeze is leaking due to aluminum porosity

12-28-2012 11:33 PM
emsvitil The cheap fix worked a little........

I skipped mild acid and went to muratic with an eyedropper.

Had baking soda solution in spark plug holes for acid overflow.


The plugs are steel, so they eventually got clean.

Soaking them in acid, then hitting them with the baking soda solution seemed to speed things up.

Wet / Dry vac to suck the water out of the spark plug holes then heat gun to dry them.

Followed by the green loctite to seal.


Anyway, there's still a leak; but it seems less than before and it does seem to be slowing down. If it eventually stops, I'll call it good.


BUT, if it doesn't stop, what's the best method of getting the plugs out.


I have an impact torx bit that will fit the plug, but my worry is stripping out the plug if I use my impact wrench.

OR

I won't strip out the bit if I use an impact screwdriver (the type that you hit with a hammer) because hitting it with a hammer keeps the torx bit in the plug while you're loosening things up. My worry is head damage while hitting it with a hammer.......


Does anyone think I can damage the head with an impact screwdriver when I hit it with a hammer?


thanks
12-22-2012 10:52 AM
whynotthinkwhynot Try this article's advice, and be careful not to strip it. IIRC, it's an aluminum plug. If it's not, heat might help, but you'd have to be careful not to heat the plug itself- just the aluminum around it. I'm not sure if I'd want to go that far, so that's a last resort IMO. Try the mix mentioned above, and let it soak in. You might want to try some minor acid action as mentioned. When you re-install the plug, I'd use loctite- blue or green- to prevent a future galvanic reaction.

Best lube for Rusty Nuts
12-21-2012 06:45 PM
emsvitil If you can't get the plug out, would this work to seal it:

1) Mild acid to clean any corrosion around and on the plug.

2) Penetrating loctite to seal it up (hopefully)
12-21-2012 06:28 PM
1turbofocus You are correct , more then likely its the plug , I have tried to remove many of these and they are VERY tight some I couldnt even get out

Tom
12-21-2012 06:08 PM
emsvitil
Coolant in #2 spark plug hole of Zetec.

Coolant in #2 spark plug hole of Zetec.

And yes, it's coolant. I dried it out yesterday (small puddle around spark plug hex at time) and today it's moist again.


The spark plug hole on forward (exhaust cam) side looks moist as if coolant is seeping thru there......


But I'm hoping that the hex head bolt just to the left of #2 (towards #1) isn't a bolt but a plug for the coolant system. (looks slightly corroded, but was dry today and yesterday). If it's a plug, I think it's the leak.


Can someone tell me if this is a PLUG (please be yes) or a head bolt?



Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:28 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.