Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > ZETEC Performance (2000-2004) > Bung size for an EGR weld-on a SVT header?

ZETEC Performance (2000-2004) The place to chat about any 2.0L Zetec engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Bung size for an EGR weld-on a SVT header? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-14-2013 12:19 PM
xsuicidesn0wmanx Ah yeah, i forgot when i got my egr parts the car hadnt made it to the back yet.
06-14-2013 12:16 PM
Magus2727 The problem with trying to find them is that most Junk yards pull the CATS (or at least they do here in Utah) and the bung is "on" the CAT pipe.
06-14-2013 11:47 AM
xsuicidesn0wmanx I had this done just 2 months ago, as long as the placement is correct it shouldnt be too hard to fit the tube onto the end of the bung. As far as getting the bung its not very hard, just go to the junk yard, find a Mk1 and take the bung out of that. Might take a little bit of effort but they just thread right out.

Only thing I can add is that I wish my weld looks as clean as the ones in the pics above, the shop I went to did a solid but ugly weld ;\
06-07-2013 09:58 PM
homelessmonkey Yeah Itll thread in no problem, but you might have to bend your egr tube a bit.
I also had to bend mine since the garage welded my bung a little off set. Easy fix though had some heat and bend :)


06-07-2013 11:24 AM
MattDzx3 Yes you can use the stock tube as long as you mock up the header to make sure that the bung gets welded in so that it lines up with the stock location. I had to bend mine slightly to make it fit.
06-07-2013 09:40 AM
joecicalese So can anyone confirm that I'll be able to use my stock Zetec EGR tube?
03-21-2013 08:14 AM
Magus2727 Any adapter that is steel or stainless steel and is the thread size M22 x 1.5 w/ 30 flair should work. That link fits the bill. You will want to check on minimum orders and lead times.

My guess is you want the 9236-22-22... assuming the 22 is referring to the metric thread size.
03-21-2013 08:05 AM
Trev FF
Quote:
Originally Posted by MattDzx3 View Post
That looks almost exactly the same as mine did using the adapter from the stock cat, btw nice wrapping job

Trev FF if you have your stock cat there is an adapter between the cat and the egr tube that I welded onto my header. Pictures of the adapter are on the previous page.
i dont want to use the one in my cat. becuz i mite want to put my stock stuff back on if i sell.
03-21-2013 12:33 AM
MattDzx3 That looks almost exactly the same as mine did using the adapter from the stock cat, btw nice wrapping job

Trev FF if you have your stock cat there is an adapter between the cat and the egr tube that I welded onto my header. Pictures of the adapter are on the previous page.
03-20-2013 05:18 PM
Trev FF
Quote:
Originally Posted by pkolator View Post
This place...

http://www.adaptall.com/products/carbonsteel/9236.html

...seems to have a lot of adapters. 9236-22-22 would be the correct size then to connect the tube to bung? I'm going to put a call into these guys tomorrow.
is that the website you order the bung from. im looking for the same fitting. and did this work?
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:53 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat