Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > Spi head gasket

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Spi head gasket Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-14-2012 02:45 AM
amc49 My stuff says.......................

go to 37 ft.lbs.

back off all 1/2 turn

go back to 37 again

go 1/4 turn more all

then go another 1/4 turn all again.




9 3 1 5 7

front

8 6 2 4 10
11-14-2012 02:29 AM
amc49 It is routine for gasket makers and others to now suggest that ALL stressed bolts like head bolts should be changed, it is more of a guarantee their part will be successful. Besides that it sells more parts...............I notice that Felpro now calls for new bolts on engines I know for a fact don't need them.

The way you tell-

if final tightening is worded as a DEGREE OF ANGLE such as 90 degrees or 45 degrees or whatever, then yes, you need to change the bolts.

if final tighten is a TORQUE, or 44 ft.lbs. or 65 ft.lbs., etc. then bolts are reuseable provided nothing has happened to them that would warrant their being changed.

SPI seems to call for a last tighten of 1/4 turn so that is 90 degree angle, so yes, bolts need to change. They get stretched out of shape at first tightening, you can blow head gasket by using them again since they are already internally yielded (TTY, or 'torque to yield', the type of bolt).
11-12-2012 01:36 PM
PuntaGorda I'm rebuilding a SOHC 2.0 SPI and have less than complete faith in the specifications provided by our trusty friends at Fel-Pro. Could I get a few second opinions on the torque specifications and end sequence for the Head Bolts? I currently have them all at 44 ft/lbs and will hold sequence until a consensus of the SPI gods has been made. Thank you.
10-05-2009 11:02 PM
a_2000_se
Quote:
Originally Posted by whynotthinkwhynot View Post
Buy new bolts, if you think you're going to be keeping that car and engine until the doors fall off, do some research and see if ARP makes bolts for the engine. Those shouldn't stretch.
Are the 'ARP' bolts torqued to the same spec's as the OEM bolts?

The SOHC are one time use, $24 - Felpro. The DOHC are rated for two uses before replacement - aren't they?
10-05-2009 08:33 PM
whynotthinkwhynot Buy new bolts, if you think you're going to be keeping that car and engine until the doors fall off, do some research and see if ARP makes bolts for the engine. Those shouldn't stretch.
10-05-2009 08:06 PM
trailbikerider They're called TTY Bolts (Torque-To-Yield) and yes, they're only good once.
10-05-2009 07:39 PM
mikebontoft did you ever get that head replaced btw? and yes IIRC bolts are one time one use unfortunately.
10-05-2009 07:37 PM
andrew3464 Hi Brandon,

According to the Haynes manual-"....the bolts are the stretch type that must be replaced with new ones whenever they're removed."

I replaced mine when I had the head resurfaced and valve job done.
10-04-2009 09:18 PM
90base
Spi head gasket

I suspect my head gasket is trash can I reuse the head studs I thought I read u could on a focus but I searched to no avail.

Tnks

Brandon

Posted via FF Mobile

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:02 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.