Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Technical Chat > belt tentioner.

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: belt tentioner. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-09-2013 03:16 PM
rallynut next time get a serpentine belt tool from your local parts store. just dont use it as a breaker bar
10-14-2012 08:19 PM
klondike jake I GOT IT.i want to thank every one for your help. i feel kinda dumb,but it just needed more force than i thought to get it to finally go. thanx again.
10-14-2012 01:31 PM
whynotthinkwhynot Wait.... are you on the bolt inside the actual pulley, or on the bolt holding the center of the tensioner arm? You should be on the bolt in the center of the actual pulley itself, moving it clockwise will rotate the pulley up so that you can slip the belt off another pulley- usually an idler where the back of the belt rides on the pulley.

As far as belt routing, you'll have to use your head on that one. If moving the pulley up and away puts more tension on the belt, then that's obviously the wrong way to go. You might want to check to be sure that your belt routing matches what is in your manual, or at least draw it out on paper before you remove the belt.

Did someone remove AC from this car or something?
10-14-2012 12:30 PM
klondike jake moving it back towards the back of the car ,i have zero movement.is it possible that it could have been put on diff to accept a diff belt.
10-14-2012 03:12 AM
emsvitil That's weird....

I just did mine because I was changing the timing belt.

How much leverage to you have? (I had about 12 inches)
10-14-2012 01:29 AM
klondike jake dosnt want to move any when pushing towards the rear of the car.
10-13-2012 10:22 PM
emsvitil From underneath the car, with the wrench hanging down from the bolt.....

You're pushing the end of the wrench to the rear of the car.


Essentially trying to tighten the bolt will tighten the tensioner against it's internal spring.

That gives you some slack in the belt.
10-13-2012 08:35 PM
klondike jake are you pushing towards the front of car or towards the rear. it wants to go towards the front but it will stop within 1.5 inches of travel.
10-13-2012 08:10 PM
emsvitil Jack front end up
Remove right front wheel
Remove the plastic panel under the belt from underneath.


It's 15mm.

An offset closed end or flare wrench won't slip off the nut.

Then from underneath push wrench (with extension) toward rear of car.

You can the slip the belt off the crank pulley.
10-13-2012 07:51 PM
Mr.Bergner I use an open end wrench (I think 15mm?) with a breaker bar attached to it (Usually have to tape it to it so it doesn't slide off). And then position it in place and push forward (counterclockwise of course).

Have you tried spraying some PB Blaster in there? Sometimes it feels like you're not really moving it much but indeed you are. Maybe get someone to test the tension on the belt while you try? And have you done it before?

oh yeah, and to Focus Fanatics!
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:57 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat