|11-12-2012 04:45 PM|
|loki993||Oh for sure and it wasn't even that it was a PITA, just a bit tedious. I called the dealer just too see and they wanted 179 to do a flush and that's not even changing the filter. Plus from what Ive been reading a flush isn't always the best thing. DIYing it and running the car to pump the fluid out seems to be the safest way to go.|
|11-12-2012 04:17 PM|
It's a messy PITA to do, especially your first time.
Getting it done right yourself makes you a LOT happier once it's complete though!
|11-12-2012 03:51 PM|
I got it done. I Unscrewed the fitting going into the trans they the cooler line hooked to like elsolo said to. Much easier then messing with that connector and possibly breaking it. It was a little tedious because there isn't much room under here but it wasn't to bad.
I pulled to line off and ran the car a bit, went through the gears, turned it off and did it all again. Got 3 maybe 3 and a half quarts that way.
The hardest part was actually getting the pan off, that RTV they had on there stuck pretty good and the plastic putty knife I bought just couldn't get in there. I ended up having to cheat a bit and I used a screwdriver to pop it off. I had to pry at it a bit until I could finally get my fingers under there and pull it off. Grrr as hard as I tried to keep cardboard and drip pans down I got some fluid on the driveway. I must have drained the car good running it because I got maybe a quart out of the pan, not much at all.
The rest was pretty straight forward. I probably spent an hour probably even longer running the car and bringing up the fluid level because I was afraid to overfill it. It took all the 10 quarts I bought plus a half I had to get from autozone, so I definitely ran enough through the trans to flush out all the old.
|11-11-2012 11:14 PM|
I put cutting line out there as a possible choice........not as necessity.
You'd be amazed at how many parts get ruined when people simply twist the one outboard nut instead of using a backup wrench. I watched that damage all day long.
Of course I'd take the screw down fitting loose first, but that's just me. Others have totally different viewpoints, not that all of them make sense. Come to think of it, maybe mine didn't either, LOL.................I got drain plugs, I can laugh at the rest.
I was just thinking about tapping into lines for addition of a cooler and translated it to draining fluid too, maybe not the best way............somebody kick me.
|11-11-2012 04:03 PM|
|11-11-2012 03:58 PM|
The Up Side To Doing It Yourself
Personally I Would Do Both Change The Filter And Fluid But If It Was Me I Would Go One Step Further And As The Car Was Running And The Fluid Was Coming Out I Would Pour New Fluid In Yes You Do Waist Some Fluid But As You Are Wasting Some Youíre Keeping Fluid Running Though The Torque Converter And That Is Pumping All That Old Nasty Stuff Out Of Your Trans System That Way When The Old Nasty Brown Looking Fluid Turns Nice Bright Red You Know Itís All Nice And Clean The Up Side To Doing It Yourself Is You Know It Was Done And It Was Done Right!
|11-11-2012 03:14 PM|
|sailor||Less chance of issues THERE to be sure!|
|11-11-2012 03:00 PM|
|elsolo||The fitting I suggest is a steel tube nut going into a steel adapter at the trans.|
|11-11-2012 02:47 PM|
I believe he WOULD advocate that, probably after prev. issues with corroded fittings & subsequent leakage.
And if you wrench too hard on a fitting into a plastic radiator, well you're buying a new radiator!
X2 on the double hose clamp though, did an emergency repair on a holed hard line last year for someone, and it leaked later 'till I doubled the clamps (opposite orientations BTW).
|11-11-2012 12:20 PM|
|elsolo||You advocate CUTTING the hardline rather than unscrewing the tube nut?|
|This thread has more than 10 replies. Click here to review the whole thread.|