Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > SPI Performance (2000-2004) > High Nox emissions after rebuild

SPI Performance (2000-2004) The place to chat about any 2.0L Split Port Injection engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: High Nox emissions after rebuild Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-02-2012 05:34 PM
SPI Tuner NOX is because you car is getting to hot. The EGR system puts burned gases back in to the cylinder to reduce NOX emissions. So yes you are right. Since I'm guessing you live in Cali the emissions standards take that into consideration. So yeah check you EGR flow with a vacuum pump on the EGR test port. If you surpass 4.2 in/hg of vacuum and the engine doesn't start to idle rough then that is your problem.
03-07-2012 10:04 PM
svtf1417 I could have sworn I learned in class that the EGR system is what helps reduce NOx, oxides of nitrogen, in emissions.
03-06-2012 08:52 PM
CaliFucos
High Nox emissions after rebuild

Hi,
I just finished rebuilding my 2001 SPI after failing my previous emissions test for slightly too much hydrocarbons and dropping a valve seat shortly thereafter.

I had the crank turned, put new bearings, pistons, rings, timing belt, timing component kit, head with hardened valve seats, head bolts, thermostat, water pump, oil pump, and all new gaskets. I cleaned the block inside and out, deglazed the cylinders, cleaned the intake manifold, egr and throttle body. Of course I also changed the oil and filter as well. I have a new radiator, I flushed the cooling system, and I put new antifreeze. Right before it dropped the valve seat I changed the air filter and oxygen sensors.

The car was running somewhat rough at times and seemed sluggish after having done all of that, I ultimately found this to be caused by the original fuel pump module lines being brittle and cracked. After replacing the fuel pump with the newer style pump and replacing the fuel filter, the car is running like it never has.

I took it to the smog station and it failed the functional check for "MIL/Check engine light test due to failure to successfully complete all OBD self tests" which I understand was caused by the fact that I don't have enough drive cycles after resetting the computer. I am not too worried about that.

What concerns me is that it failed the sniffer test as well, here are my results:
15mph FAIL
RPM 1833
CO2 14.7
O2 0.1
HC 46 MEAS 61 MAX
CO 0.20 MEAS 0.54 MAX
NO 816 MEAS 467 MAX

25mph PASS
RPM 1759
CO2 14.7
O2 0.1
HC 31 MEAS 45 MAX
CO 0.15 MEAS 0.53 MAX
NO 751 MEAS 754 MAX

So far, I have checked for vacuum leaks and I found none, I also checked my pcv valve and it was not clogged, however I did notice that I just barely had it twisted into the hole, so it could have been sucking air from the environment rather than the actual crankcase. I checked the EGR for function by unhooking the line going from the egr regulator and attaching it directly to the egr valve, at which point the idle became extremely rough and the motor died, as it should. I noticed that with the egr regulator hooked up correctly I could not seem to get any vacuum on the line that goes from the regulator to the top of the egr valve, even when I revved the motor above 2,000 RPMs, does this indicate that I have a faulty egr dpfe or vacuum solenoid? I used generic O2 sensors from ebay that I had to splice in, could this be my problem?

Also the engine has less than 25 miles so I don't know it that could be part of my problem. I didn't heat my cat up by driving on the freeway like I normally do right before smog, but my car was up to operating temp.

Any help with this issue would be greatly appreciated! I really need to get this thing back on the road and I would hate to have to shell out the money for a "hot smog" when my car is completely stock and passes the smog test in every other aspect.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:59 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat