Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > Focus Tuning Chat > Adding wideband to datalog list

Focus Tuning Chat Discuss performance tuning options for your Ford Focus.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Adding wideband to datalog list Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-17-2012 03:52 PM
ZXthrizzle05 check your vaccuum hoses as wel. i had surging and high rpm with no idle due to a kinked pcv hose. so i yanked that thing out and plugged it up where it goes to the inlet manifold and runs like a champ
04-09-2012 07:55 PM
cjespers No ideas? Cool. I'm going to call SCT.

Pretty weird that Tom's log list works fine, but when I add items to it, only Tom's items will log.

FWIW: I bought this car not running. Put a new O2 sensor on (and TONS of other parts)
I always had a problem about 1 minute after startup; it would go extreme lean (18:1 or leaner) for a few minutes,then get better. But always ran poorly, surging, terrible throttle response.
I just replaced the O2 sensor again and it runs GREAT!! Never got an O2 code!!.
Crazy!!
Thanks to everyone for your support!!
Carl
04-07-2012 05:48 PM
cjespers I just returned to stock tune and updated the SCT Programmer.
No luck.
Running livelink 6.5

Yes, my wideband is AEM.

I added maf counts and a few more non analog items to the list in addition to the analog1 for the wideband.

None of them datalog. Just the items on Tom's Zetec config file will datalog.

So this narrows it down (a little).
The issue is: not datalogging ANY items added to Tom's Zetec config list, not just analog.
What could be causing this headache? Ideas? Please Help
Thanks
04-01-2012 07:13 PM
1turbofocus Choose a new list with say RPM , maf counts and analog and see if it logs , if it does keep adding to the list till you find the problem

Do you have a AEM wide band if not things wire Diff

Has your xcal been updated and are you using the LL 6.5

Tom
04-01-2012 01:45 PM
cjespers Need Advice.
Had SCT3 for a year, need to get the car tuned. Datalogging the wideband has been
Frustrating to say the least..
OK, finally realized how to add analog to Tom's zetec list. (progress at last, lol)
It's not data logging (analog ). I have checked the firewire pinout for the AEM wideband several times.
Set up analog channel/AEM Wideband in the tuner, started livelink, loaded Tom's Zetec log list (with analog added) set up the analog equations in livelink.
Hit green button, everything is datalogging but analog .
I even tried switching to analog 2, no luck.
I'm getting 3-4 volts from the wideband to the firewire,depending on the AFR of course.
Any Ideas??
03-06-2012 06:25 PM
bespurcell I have no idea.
03-06-2012 08:07 AM
svtf1417 Do you know if your ecu is RLA1 or RLA6? I know it's not relevant, it's for my own curiousity
03-04-2012 09:12 PM
bespurcell I figured it out. DOH! It was in the Livelink config. list.
03-04-2012 08:26 PM
bespurcell
Adding wideband to datalog list

I set up the datalog list using the file Tom made for a zetec. I even found out how to add my AEM wideband to the list(analog 1). When I hit the button to start datalogging nothing would happen. After closing the program a few times and messing around I finally got it to datalog but without the analog 1 channel for my wideband. I don't know what I did to get it there the first time. It's like the option no longer comes up anywhere. So can someone please tell me how to add the analog channel to the livelink datalog list?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:50 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.