Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Technical Chat > Common Ford Focus Transmission Problem, How to fix

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
FocusFest FocusFanatics Merchandise

Thread: Common Ford Focus Transmission Problem, How to fix Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
Today 09:57 AM
JONNY750 Thanks I did placed it neutral saw the timing marks and replace it with the marks aligned
Today 05:22 AM
amc49 It has to be adjusted properly too.
Yesterday 09:16 PM
JONNY750 Does not always shift hard out of first
Yesterday 09:00 PM
JONNY750
trans problems

2001 zx3 shifts hard out of 1st. any ideas
had po705 code replaced range module still the same
Thanks for time
04-26-2015 12:10 AM
Ex-Calif Drove it again tonight. Definitely 2-3. Only happens under lighter acceleration. Moderate acceleration or heavy acceleration it shifts clean - Intuition would say a pressure problem. Higher rpm = higher pressure?

Sold my '67 Chevelle for $1500 in 1981. Shoulda put it in a barn...

Also put a 400 small block in a Datsun pickup but that's another story for another forum - LOL...
04-25-2015 02:01 PM
amc49 The servo controls 2 and 4 so any combination of going into 2-3 or 3-4 can show up there. Slips too early coming out of 2 and slips late going into 4.

I used to put Vega converters in Turbo 400s behind 454 BBC to get cheap man's hi-stall converter...we at one time had a 2 speed Powerglide that ran in the mid 9's at 140 mph 1/4 mi. '70 Corvette............we should be shot for butchering that car, I groan to think of what a '70 with 454 4 speed would bring now............
04-25-2015 08:49 AM
Ex-Calif
Quote:
Originally Posted by amc49 View Post
.

If the problem is 3 to OD shift then servo piston can break loose its' pin to do that or servo may simply need another longer band bolt, it has worn band enough so that it slips slightly and both issues can be erratic. Bolt on the other end of band from servo comes in slightly different lengths to do that, but common for trans shops to tell you you need a new trans in lieu of that quick fix, it makes them far more money. Both 3 and 4 use the direct clutch pack too, high mileage trans end cover wear can make for direct clutch hydraulic circuit leaks that produce that slip occasionally. Usually reverse suffers first but not always.

PCM can only point towards solenoid issues because that is the only thing that can be electrically detected, it cannot deduce exact mechanical problems. When a solenoid code pops up, it should be more widely interpreted as could be anything that solenoid plays with including hard parts, the wiring to the solenoid could easily be frayed or broken internally as well.

..
This is excellent info and you definitely sound like you know this tranny well. Thanks for sharing. I've read some of the other posts about how to get into the tranny and fix some of the realtively "common" wear out parts and failures. I am not shy about that kinda stuff once I get my garage and get it organized.

To be honest I may be having a senior moment. The shift slip may be 2-3 not 3-4. I will have to double check. I am not driving "his" car since I got my new (to me) Jeep Liberty.

That animal (a 2012) has its own list of demons that can pop up - LOL...

As for all this electronic mumbo jumbo today? It's our fault. It started sme time in the mid '70s the day I put electronic points on my '67 Chevelle 327 to get a hotter spark - LOL...

Look what we started - The good old "Powerslide" transmission didn't have any freakin' wires going to it or in it. Just a vacuum tube (and a high stall torque converter) - LOL...
04-25-2015 08:37 AM
Ex-Calif
Quote:
Originally Posted by amc49 View Post
I don't hesitate to reuse ATX oil at all IF IT'S GOOD AND CLEAN.

Driving 2K on no OD didn't hurt anything by itself, old school cars drove without any OD at all and the trans ratio was still 1 to 1 like these are in 3rd gear. The fluids lasted 60K doing that and these use synthetic which goes even longer. The old school trannies also slipped converter all the time, these lock it with a clutch and that lowers trans fluid heat tremendously. Heat is what turns the fluid from red to orange and then brown to be dark.
.

<snip>

Look up my posting on how to get key to turn on forever after it starts not turning on, after lock cylinder is in your hand 30 seconds of work and zero $$$ to fix it pretty much forever. DON'T wait until it won't come out, you may have to drill it out then, most do. better done before it becomes a problem.

I as well personally remove the solenoid under the shifter, whoops! missing parts cause no problems.......................
After son drove 2,500 miles with no OD the fluid was (in hindsight) very dark. I am sure he cooked it. When I got there and we drove on the freeway I am sure the RPM was over 3,500. That's what made me notice the problem in the first place.

Fluid is cheap comparitively. I wouldn't save $20 when changing out the solenod.

I am in with the shifter soelnoid and key problem. But these fixes are also cheap to do it back to original. New shifter is like $50 and the key barrel and coding is a no brainer.

Totally agree to do the key before it needs it.

My kid also wants to do some customizing on the car and I figure there could be some good summer projects in it for him and I to get some bonding time in before he heads off to the Navy later this year.

Only a few months left to pass on fatherly "wisdom" like how not to get ripped off by auto mechanics, plumbers etc... OK my estrogen level is getting too high I better stop here - LOL...
04-25-2015 08:29 AM
Ex-Calif
Quote:
Originally Posted by Marde View Post
Hi, welcome to FF.

If me, and doing it a second time, I would buy the whole kit $159 (LINK) and replace all 6 solenoids. No sense (to me) in buying another SSA or $200-SSC from your local Ford dealer.

Classic bad SSA symptoms are sometimes fixed after second repair effort by replacing SSB. Do not remember if someone got a second-effort fix with SSC replacement, but it too is a player during EPC control verses throttle position. Your slips/failures do seem like they are showing up at some and not all throttle demands tho....

GL.
Great tip and thanks for the link. It's got about 3,000 miles since the last fix including a California to Ohio trip. Other than a slight slip in teh shift it's holding up.

Move into house in 3 weeks. Can't wait to have a garage again...
04-18-2015 04:47 PM
amc49 I don't hesitate to reuse ATX oil at all IF IT'S GOOD AND CLEAN.

Driving 2K on no OD didn't hurt anything by itself, old school cars drove without any OD at all and the trans ratio was still 1 to 1 like these are in 3rd gear. The fluids lasted 60K doing that and these use synthetic which goes even longer. The old school trannies also slipped converter all the time, these lock it with a clutch and that lowers trans fluid heat tremendously. Heat is what turns the fluid from red to orange and then brown to be dark.

If the problem is 3 to OD shift then servo piston can break loose its' pin to do that or servo may simply need another longer band bolt, it has worn band enough so that it slips slightly and both issues can be erratic. Bolt on the other end of band from servo comes in slightly different lengths to do that, but common for trans shops to tell you you need a new trans in lieu of that quick fix, it makes them far more money. Both 3 and 4 use the direct clutch pack too, high mileage trans end cover wear can make for direct clutch hydraulic circuit leaks that produce that slip occasionally. Usually reverse suffers first but not always.

PCM can only point towards solenoid issues because that is the only thing that can be electrically detected, it cannot deduce exact mechanical problems. When a solenoid code pops up, it should be more widely interpreted as could be anything that solenoid plays with including hard parts, the wiring to the solenoid could easily be frayed or broken internally as well.

Look up my posting on how to get key to turn on forever after it starts not turning on, after lock cylinder is in your hand 30 seconds of work and zero $$$ to fix it pretty much forever. DON'T wait until it won't come out, you may have to drill it out then, most do. better done before it becomes a problem.

I as well personally remove the solenoid under the shifter, whoops! missing parts cause no problems.......................
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:27 PM.


Copyright 2002-2015 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Mazda CX-3, Audi S3, Mazda MX-5 Miata and Acura TLX. You can find all Ford Focus, Focus ST and Focus RS related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. If you own other makes have a look at Challenger Hellcat Forum, Charger Hellcat Forum, Cadillac ATS-V Forum, Cadillac ATS Forum, Cadillac CTS-V Forum, Lexus RC-F Forum, Lexus GS-F Forum, Mercedes GLA Forum, Mercedes GLE Forum, Civic Type-R Forum and Volvo XC90 Forum.





Search Engine Optimization by vBSEO 3.6.1