Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > ZETEC Performance (2000-2004) > Fuel Pump Strainer Part #

ZETEC Performance (2000-2004) The place to chat about any 2.0L Zetec engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Fuel Pump Strainer Part # Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-12-2014 10:26 AM
amc49 .............and some two years later............

'Do you also use water and compressed air to clean your inline fuel filter?'

No, the filter matrix is often paper or some sort of paperlike compound there. BUT, I have cleaned them to reuse before, yes. As long as they flow well they work fine. A simple backflow can remove huge amounts of deposit there. I shake them while full of fuel and then drain it backwards. Blow out LIGHTLY with air, no hard pressure applied. They work fine afterward on the cars.

I'd also like to point out the OP pic showing strainers of a double layer media, the ones I reuse are only single but they can be opened back up much easier than the two part media can, the finer opaque layer clogs up and will not unclog easily since the outer layer prevents trash from falling away from the inner. Probably best to not waste time trying to clean that two layer one there in pic. The single layer OEM one is durable plastic and even though stained they can be very 'pores open' and work like new. Why I don't toss the OEM one if that single layer stuff............

Yes new filter/strainer for ten bucks, big deal. Clean one to use over in 5 minutes or less, that's 1/12th hour, lemme see, 12X$10=$120/hr. payrate, please tell me who pays you that? Money is everywhere to be made at far less work than you do all day long, just open your eyes.............it's the small costs that add up to kill you.
06-05-2013 01:49 PM
cwczx3 Just an FYI there are two strainers on our pump modules the FS216 is the external strainer and FS209 is the internal strainer that is right on the pump and is more likely to clog.



Here is a shot of the inside of the canister showing the dirt that collects there. I only had about 65,000 miles on this and that's how much junk was in there.

12-18-2012 12:25 PM
iminhell New one costs a whopping $10.
I see no issue with replacing vs trying to clean.

Do you also use water and compressed air to clean your inline fuel filter?
12-18-2012 02:59 AM
amc49 Those socks can be stained as hell and still be cleaned to work like new, the trick is to use water, the water takes off ethanol borne crap that solvent will not touch. I simply use mine over after a good cleaning and compressed air blowout. It will be stained but the pores are open like a new one, driving on 4 different cars done like that for years. I wouldn't buy new strainer unless it's damaged, have never ever had to in countless cars and 45 years driving.
04-21-2012 08:34 PM
hero of tomorrow Thanks!
04-21-2012 05:07 PM
mikebontoft just go to any parts house and they will be able to find either the airtex FS216 or cross over to another brand.

Just for the record, the reason they don't list just the strainer is because every fuel pump for this car comes WITH a strainer.
04-21-2012 04:54 PM
hero of tomorrow Hi Guys,
Just started working on this -

the fuel pump access tutorial I found on this forum is below

http://www.focusfanatics.com/forum/showthread.php?t=276213

I went to the junkyard first to make sure they had a donor focus. I drilled holes in the corners of the square of metal over the fuel pump and used a hammer and screwdriver to cut the metal - no problem cutting hoses etc. - though very very slow and arduous going. While I was there i pulled the fuel pump out too! (can't hurt to have a spare, right?).

However, the sock looks pretty dirty. I'd like to know if you have any recommendations for where to get a new one specifically?

The one you posted does not look like the same part (different bag shape) - does this matter?
05-03-2010 01:40 PM
iminhell I cut with a tin snips. Kinda why it is an ugly hole.

I have had the open hole for years now. Have never got water up there. Will get a little dust through the hole but nothing real bad. A little access door would be nice, but I have no clue what I did with the chunk I cut out.
05-03-2010 11:09 AM
focusmaniaczx3 you dont lol
BTW PLEASE!!!!
be extremely careful doing this. as you can see it is very close there and if you get too excited you could easily cut through to your gas tank. also be careful and consider carefully whether you want to do this or not. if you accidentally cut through the tank and send a spark into the tank you could be quite badly burned or even killed. it would be safer by a long stretch to just drop the tank and if you want THEN cut the hole. i just wanted to air on the side of caution. do as you please
05-03-2010 11:08 AM
devanZX3 DUCT TAPE
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:14 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat