Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum

Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum (
-   Ford Focus Builds & General Showroom (
-   -   Just a little off the hard top... LOTS OF PICS (

Flying56eagle 04-13-2010 08:26 AM

Just a little off the hard top... LOTS OF PICS
Installed the sliding ragtop on Sun, (I will say I got the ideal from seeing it on a members 4 door ride on here, so yes I copied some one, and glad I did) It's a 35"X35" sliding ragtop from streetbeat, $368.00 labor was quoted around $400-$600 Did it myself..

Before you start do have only one..

Then read all the directions before you start
Make your template and MAKE SURE IT IS SQUARE..
Place the template on the inside first and then on the roof CENTER IT And then adjust front to rear as needed, Then tape it down and mark it.

Place the frame on top to make sure it is were you want and NEED it

Then remove your head liner if needed, IN NEWER MODLES I WOULD BECAUSE OF CURTANT SIDE AIRBAGS.

Make sure you unplug all wires

Cover the interior to protect it


Drill your pilot holes, I used a magnet to help grab the savings

Cut your lines out, and also have someone help at the last cuts to hold top up while cutting

Make sure you check your cut line...

And Finish your cuts

Use a fine file to clean all the edges and your corners

Place your frame back on to make sure it fits , DO NOT FORCE IT. Mark your holes and pre drill them, remove frame and enlarge holes as
needed, use 1/4 bead of really good silicone sealant, And bolt it down checking your work as you go.
Replace your headliner and when you TRIM it MAKE SURE YOU GIVE YOUR SELF 3" OF PLAY for the pinch molding, And be careful of any wires.

All in all it took around 6 to 7 total hours, for someone that has never done this before, not to bad.. and it wasn't to hard to do.. Just Make sure it is what you want..

The interior headliner was tough because the fabric has a fiberglass backing, glued to a 1/8" sheet formed fiberglass panel, so I will have to steam the fabric to take out the creases.

Still have some cleaning and touch up, and need to steam out the creases on the headliner, and will post some pics when all is done and cleaned..

hypnoticracing 04-13-2010 08:30 AM

wow deifantely unique.. looks like you took your time and di it right though

1sloho 04-13-2010 09:04 AM

wow man. great job. takes some balls to cut a huge hole in ur roof!!

Hitaway 04-13-2010 09:18 AM

Looks good, that had to take some guts to cut into your car. I bet the beer helped, lol.

Yocrew 04-13-2010 09:19 AM

Wow, first really big move on a new coupe. That's something you can't take back. You have a rep from me sir, and I never give them out.[thumb]

GrndZero 04-13-2010 09:40 AM

Not only is that a great idea and looks like it was done very well. You have one awesome garage!

puppetman 04-13-2010 09:50 AM

thats very impressive! i like it alot! and you did it with beer!

Rafal 04-13-2010 10:00 AM

meen if I would try do to something like that I would have a convertible, nice JOB very clean to :)

fhh02a 04-13-2010 10:12 AM

as they guts, no glory....

well sir you have guts and glory...... cause there is no way in hell that I would do that

slipster17 04-13-2010 10:20 AM

awesome Ron, simply awesome. Can't wait to see this at one of the meets over the summer.

To be entirely honest, when you talked about doing this at Tunerwars, I didn't think you would actually follow through with it! lol.

All times are GMT -5. The time now is 02:47 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.