Rear Bearings - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > Brakes, Suspension & Body Chassis

Brakes, Suspension & Body Chassis The place to go for answers on brakes, suspension, camber, alignment and more.

Search This Forum | Image Search | Advanced Search    
FocusFest FocusFanatics Merchandise

Reply
 
LinkBack Thread Tools Display Modes
Old 05-08-2014, 02:03 PM   #1
Focus Rookie
 
Join Date: Jun 2012
Fan#: 100745
Location: Twin Cities, MN
What I Drive: 2001 Silver ZX3

Posts: 19
FF Reputation: 1 silver zx3 Good Standing Member
Buy-Sell-Trade Rating: (0)
Question Rear Bearings

Hey guys. I have a '01 ZX3. I've had the rear bearings swapped twice now, making this the third time they have gone bad in less than a year. Something is seriously wrong and I don't know what it is.

In the past six months I've replaced the rear Strut/Shock while keeping all of the same bushings and mounting hardware. The bearings being messed up has been happening before the strut replacement. I have a warranty on the bearings/drum for a year but I am getting tired of pulling them off and having to swap them out.

I have not tried replacing the axle nut yet, heard I should try that. The axle itself looks to be in perfect condition, not scratched or marks digging into it.

Another weird thing is that my E-brake doesn't work. You pull on it and it is so tense that you cannot even get it up one click. I looked at the cable connecting to the metal "lever" it is connected to inside the drum and it is rusted solid and might not even disconnect from the lever.

Manager as work said it could be bushings on the shock that is kicking it in a wrong angle putting too much pressure on it or I think it might be the E-Brake cable putting too much tension on the brakes and wearing out the bearing by being in the wrong position.

I've had the car for just under 3 years, replaced the shoes in the drum when I first got it. Shoes appear to be in good condition, same with all the springs in there. Both bearings seem to go bad around the same time. They start making a humming noise and progressively get louder and louder over time. Had one of them actually pop and break a few of the metal cylinders in the bearings(fixed it immediately though). Been happening for roughly a year and just need some help on where to go next.
Thanks guys! Sorry about it being lengthy, figured I'd give as much info as possible.


silver zx3 is offline  
    Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 05-08-2014, 02:48 PM   #2
Vince your Moderator
 
freemind's Avatar
 
Join Date: Jul 2009
Fan#: 67513
Location: Seattle, WA
What I Drive: 2002 ZX3 and a 2010 Focus SE (Work)

Posts: 5,042
Points 7,246, Level 56
Points: 7,246, Level: 56 Points: 7,246, Level: 56 Points: 7,246, Level: 56
Level Up 48% Completed
Level up: 48% Level up: 48% Level up: 48%
Forum Activity 0%
Activity: 0% Activity: 0% Activity: 0%
FF Reputation: 24 freemind Great Standing Member
Buy-Sell-Trade Rating: (23)
Use Timken or, SKF Bearings only. They MUST be torqued to 173 ft/lbs. or they will wear out quickly.

As far as the E brake, you will have to remove the console to make sure that the cable is hooked up there and/or, look at the cable at the drums as well, trace it to make sure that it has not broken.

Post results.
__________________
133whp-126ftlbsTQ Eclipse CD8443,Eclipse PA5422, JBL GTO751EZ, PPI 356cs(Rebranded A/D/S 346cs), JBL p1024, SubThump enclosure, RAAmat BXT, Damplifier Pro

Hatch Nation #140
Caeci caecos ducentes
freemind is offline  
    Reply With Quote Quick reply to this message
Old 05-08-2014, 02:50 PM   #3
Focus Fanatic
 
Marde's Avatar
 
Join Date: Jun 2013
Fan#: 115991
Location: Mesa, AZ
What I Drive: 2004 ZTW PZEV 2.3 ATX

Posts: 2,190
Points 3,184, Level 34
Points: 3,184, Level: 34 Points: 3,184, Level: 34 Points: 3,184, Level: 34
Level Up 90% Completed
Level up: 90% Level up: 90% Level up: 90%
Forum Activity 59%
Activity: 59% Activity: 59% Activity: 59%
FF Reputation: 23 Marde Great Standing Member
Buy-Sell-Trade Rating: (0)
There are many cheap brands of bearings and you will have a greater chance of failure dependent on the brand you used. You need to re-build the drums/shoes again and get the e-brake thing sorted out. Yes, especially in your situation, get new retaining nuts.. about 20 bucks each. When you do it, make sure you do it with a torque wench that can do 175 ft lbs.

FYI - I just did similar and used new drums with bearing using (yes a cheap Chinese bearing) Duralast brand ->
Duralast Drums with same p/n but are different
__________________
You've got to ask yourself one question: Do you feel lucky? -and could you really drive a Focus ATX Wagon?
Marde is online now  
    Reply With Quote Quick reply to this message
Old 05-08-2014, 08:43 PM   #4
Focus Enthusiast
 
Buildist's Avatar
 
Join Date: Mar 2014
Fan#: 150994
Location: North Olmsted, OH
What I Drive: 2012 Blue Focus SE

Posts: 128
Points 272, Level 5
Points: 272, Level: 5 Points: 272, Level: 5 Points: 272, Level: 5
Level Up 44% Completed
Level up: 44% Level up: 44% Level up: 44%
Forum Activity 3%
Activity: 3% Activity: 3% Activity: 3%
FF Reputation: 1 Buildist Good Standing Member
Buy-Sell-Trade Rating: (0)
I did rear bearings on a ZX2. I don't know if they are the same.

RUN away from National brand bearings (Korean junk). I put 5 of them on a 1996 Sable before I got Ford bearing hubs and fixed it right. The Nationals wouldn't even make it aroung the block, literally.

I got the SKF bearings for my ZX2 and I think they were made in USA. Some of them are, some are Canadian, and some are Mexican, I think. Be sure to get quality parts.

As others said, definitely get the brake cable worked loose at the lever. PB Blaster is our friend. If you have to get a new lever they are about $55 each from Ford. You will not find them anywhere else.

The brake cable issue could be frozen (rusted) levers not allowing movement, rusted cables, or something right at the handle.


Steve
Buildist is offline  
    Reply With Quote Quick reply to this message
Old 05-08-2014, 10:44 PM   #5
Hammer Down
 
sailor's Avatar
 
Join Date: Jun 2008
Fan#: 57268
Location: Williamsville, NY
What I Drive: 2004 Pitch Black ZTS 2.3 5spd.

Posts: 24,354
Points 16,916, Level 83
Points: 16,916, Level: 83 Points: 16,916, Level: 83 Points: 16,916, Level: 83
Level Up 14% Completed
Level up: 14% Level up: 14% Level up: 14%
Forum Activity 100%
Activity: 100% Activity: 100% Activity: 100%
FF Reputation: 93 sailor Excellent Standing Member
Buy-Sell-Trade Rating: (0)
Moved to "Brakes, Suspension & Chassis".

Torquing them right is imperative as mentioned earlier, new nuts required to HOLD them at the right torque since they can only be re-used a time or two & be sure to hold.

Fixing the brakes while apart would be a good idea.... Rusted solid adjusters won't do the job, need replacement if you can't clean them up & get 'em working again.
__________________
"Rubber Side Down"

S.R. #275
Focus Takeover #003 / Tarbo Fan #003
sailor is offline  
    Reply With Quote Quick reply to this message
Old 05-09-2014, 09:14 AM   #6
Focus Rookie
 
Join Date: Jun 2012
Fan#: 100745
Location: Twin Cities, MN
What I Drive: 2001 Silver ZX3

Posts: 19
FF Reputation: 1 silver zx3 Good Standing Member
Buy-Sell-Trade Rating: (0)
Thank you for all the responses gentlemen. I am planning on doing them this weekend. I will pick up some different bearings and nuts to give that a try. Are the beari ngs easy to pull in and out without a press or would I need to take it somewhere to get them pressed in?
silver zx3 is offline  
    Reply With Quote Quick reply to this message
Old 05-09-2014, 12:14 PM   #7
Hammer Down
 
sailor's Avatar
 
Join Date: Jun 2008
Fan#: 57268
Location: Williamsville, NY
What I Drive: 2004 Pitch Black ZTS 2.3 5spd.

Posts: 24,354
Points 16,916, Level 83
Points: 16,916, Level: 83 Points: 16,916, Level: 83 Points: 16,916, Level: 83
Level Up 14% Completed
Level up: 14% Level up: 14% Level up: 14%
Forum Activity 100%
Activity: 100% Activity: 100% Activity: 100%
FF Reputation: 93 sailor Excellent Standing Member
Buy-Sell-Trade Rating: (0)
Pressed is the best/easiest method.
__________________
"Rubber Side Down"

S.R. #275
Focus Takeover #003 / Tarbo Fan #003
sailor is offline  
    Reply With Quote Quick reply to this message
Reply

Bookmarks & Social Networks

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
What I Drive
Year, color, and model of your car. Example: 2003 Pitch Black ZX3
Name
Your real name.
City
State
Country
Insurance
Please select your insurance company (Optional)

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -5. The time now is 10:56 AM.


Copyright 2002-2015 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Mazda CX-3, Audi S3, Mazda MX-5 Miata and Acura TLX. You can find all Ford Focus, Focus ST and Focus RS related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. If you own other makes have a look at Challenger Hellcat Forum, Charger Hellcat Forum, Cadillac ATS-V Forum, Cadillac ATS Forum, Cadillac CTS-V Forum, Lexus RC-F Forum, Lexus GS-F Forum, Mercedes GLA Forum, Mercedes GLE Forum, Civic Type-R Forum and Volvo XC90 Forum.





Search Engine Optimization by vBSEO 3.6.1